三菱PLC,欧美a级片免费看,三菱变频器,欧美a级成人淫片免费看,三菱伺服,欧美a大片,三菱电机--广州凌控

廣州正菱|三菱
當前位置:首頁 >> 資料下載 >> 三菱 >> FX系列PLC >> 三菱 FX2NC 三菱-FX2NC-4DA 用戶 手冊
三菱 FX2NC 三菱-FX2NC-4DA 用戶 手冊
所屬類別:三菱 >> FX系列PLC
資料介紹:

s
O


following items:
O = 0:Sets the voltage output mode (-10 V to 10 V).
O = 1:Sets the current output mode (4 mA to 20 mA).
O = 2:Sets the current output mode (0 mA to 20 mA).
Switching the output mode resets the I/O characteristics to the factory-default
characteristics. Refer to the performance specifications described in section 5.
Example: H2110CH1: Voltage output (-10 V to 10 V)
CH2 and CH3: Current output (4 mA to 20 mA)
CH4: Current output (0 mA to 20 mA)
[BFM #1, #2, #3 and #4] Output data channels CH1, CH2, CH3, and CH4
BFM #1: Output data of CH1 (Initial value: 0)
BFM #2: Output data of CH2 (Initial value: 0)
BFM #3: Output data of CH3 (Initial value: 0)
BFM #4: Output data of CH4 (Initial value: 0)
[BFM #5] Data holding mode
While the programmable controller is in the STOP mode, the last output value in
the RUN mode will be held. To reset the value to the offset value, write the
hexadecimal value in BFM #5 as follows:
O = 0: Holds the output.
O = 1: Resets to the offset value.
Example: H0011 CH1 and CH2 = Offset value CH3 and CH4 = Output holding
[BFM #8 and #9] Offset/gain setting command
Changes offset and gain values of channels CH1 to CH4 by writing 1 to the
corresponding Hex digits of BFM #8 or #9. The current values will be valid until
this command is output. (Refer to Chapter 9)
1 to 4: Channel number O = 0: No changes done. O = 1: Change data value.
[BFM #10 to #17] Offset/gain data
The offset and gain values are changed by writing new data to BFM #10 to #17.
The units of the data to be written are mV or µA. The data should be written and
then BFM #8 and #9 set. Note that the data value will be rounded down to the
nearest 5mV or 20µA.
[BFM #20] Initialize
When K1 is written in BFM #20, all values will be returned to the factory-default.
(Note that the BFM #20 data will override the BFM #21 data.)
This initialize function is convenient if you have an error in adjustment.
[BFM #21] I/O characteristics adjustment inhibit
Setting BFM #21 to K2 inhibits the user from inadvertent adjustment of I/O
characteristics. The adjustment inhibit function, once set, will be valid until the
Permit command (BFM #21=K1) is set. The initial value is K1 (Permit). The set
value will be retained even after power-OFF.
BFM #8 BFM #9
Bits b4 to b9, b11, b13 to b15 are not defined.
[BFM #30] Identification code
The identification code for a special function block is read using the FROM
instruction. The identification code for the FX2NC-4DA unit is K3020.The
main unit can use this facility in the program to identify the special function
block before commencing any data transfers from and to the special
function block.
Note:
Values of BFM #0, #5, and #21, are stored in the EEPROM memory of the
FX2NC-4DA. BFM #10 to #17 are copied to EEPROM when the gain/offset
setting command BFM #8, #9 is used. Also, BFM #20 causes the resetting
of the EEPROM memory. The EEPROM has a life of about 10,000 cycles
(changes), so do not use programs which frequently change these BFMs.
A mode change of BFM #0 automatically involves a change of the
corresponding offset and gain values. Because of the time needed to write
the new values to the internal EEPROM memory, a delay of 3 s is required
between instructions changing BFM #0 and instructions writing to the
corresponding BFM #10 through BFM #17.
Therefore, a delay timer should be used before writing to BFM #10 through
#17.
(Refer to chapter 9.)
7. Operation and Program Examples
If the factory-default I/O characteristics are not changed and the status
information is not used, you can operate the FX2NC-4DA using the following
simple program. For the FROM and TO instructions, refer to the FX
Programming Manual (II).
CH1 and CH2 : Voltage output mode (-10 V to 10 V)
CH3 : Current output mode (4 mA to 20 mA)
CH4 : Current output mode (0 mA to 20 mA)
7.1 Operation procedure
1) Turn OFF the power of the PLC, and then connect the FX2NC-4DA. After
wards, wire the I/O lines of the FX2NC-4DA.
2) Set the PLC to STOP, and turn ON the power. Write the above program
then switch the PLC to RUN.
3) Analog values will be sent from D0 (BFM #1), D1 (BFM #2), D2 (BFM
#3), and D3 (BFM #4) to the respective output channels of the FX2NC-
4DA. When the PLC is in STOP, the analog values set before stopping
the PLC will remain output. (The output will be held.)
4) When the PLC is in STOP, the offset values can also be output. For a
detailed description, refer to Section 6).
b10 Range error output value is out of the
specified range.
value is in the
specified range.
b12
G/O-
Adjustment
prohibit
status
BFM #21 is not set to "K1". Adjustable status
M8002
initial pulse
TO K0 K0 H2100 K1
Write the data for CH1 to
D0, CH2 to D1, CH3 to D2
and CH4 to D3.
TO K0 K1 D0 K4
M8000
RUN
monitor
Write data in respective data registers while
observing the following ranges:
Data register D0 and D1: -2,000 to 2,000
Data registers D2 and D3: 0 to 1,000
(H2100) → BFM #0
CH1 and CH2: Voltage output
CH3: Current output (4mA to 20 mA)
CH4: Current output (0 mA to 20 mA)
Data register D0 → BFM #1 (output to CH1)
Data register D1 → BFM #2 (output to CH2)
Data register D2 → BFM #3 (output to CH3)
Data register D3 → BFM #4 (output to CH4)
PLC FX2NC-32MT-DSS
PLC FX2NC-32MT-D/UL
RS-232C適配器 FX2NC-232ADP
PLC FX2NC-96MT-DSS
可編程控制器 FX2NC系列
轉換適配器 FX2NC-CNV-IF
RS-485適配器 FX2NC-485ADP
PLC FX2NC-64MT-DSS
PLC FX2NC-16MT-D/UL
RS-485適配器 FX2NC-485ADP
PLC FX2NC-16MR-T-DS
RS-232C適配器 FX2NC-232ADP
PLC FX2NC-16MT-DSS
PLC FX2NC-96MT-D/UL
PLC FX2NC-64MT-D/UL
三菱 FX2NC 三菱-FX2NC-4DA 用戶 手冊     三菱 FX2NC 三菱-FX2NC-4DA 用戶 手冊
相關下載
主站蜘蛛池模板: 天然气车船展、氢能装备展、氢燃料汽车展、核电装备展、国防信息化装备展---北京企发展览服务有限公司 | 千斤顶-超薄电动千斤顶-电动液压千斤顶-液压螺母扳手-泰州杰克液压机械制造有限公司 | 深圳PCB电路板厂|PCB线路板厂|FPC柔性电路板厂|FPC软性线路板生产厂家|恒成和电路板:18681495413 | 珀金斯动力设备扬州有限公司| 木马交互设计研究中心 ,专注于用户体验与人机交互设计 - 首页 | 深圳货柜租赁_集装箱出售/租赁_集装箱改造_鹏泰集装箱 | 芜湖表面处理-涂装-精密加工-阳极氧化-芜湖研历光电科技有限公司 | 疝灯试验箱-有风源淋雨-汽车盐雾室-无锡苏南试验设备有限公司 | 烧碱-工业片碱-火碱价格-氢氧化钠厂家-巩义市宝莱新材料厂 | 以物联网技术为核心专注于智能安防领域物联网服务的高新技术企业-北京欣智恒科技股份有限公司(官网) | 密集架,密集柜,智能密集架,档案密集架,智慧档案馆(室)一体化建设 | 久久91精品久久91综合_国产亚洲自拍一区_国产精品第1页_亚洲高清视频一区_91成人午夜在线精品_亚洲国产精品网站在线播放_亚洲国产成人久久综合区_国产精品亚洲专区在线观看_免费视频精品一区二区三区 | 做网站_网站建设_专业上海网站制作_网至普网站建设 | 机锋网-畅享科技品质生活,尽在机锋网| 济南海纳特科技有限公司| 柔性防水套管_刚性防水套管-河南恒生管道制造有限公司 | 江门市金环电器有限公司 | 油罐_双层油罐_双层油罐厂家|值得信赖-泰安晟鼎金属容器制造有限公司 | 热熔胶涂布机-青岛三人行机械有限公司| 上海新航道学校官网_20年专注雅思_托福_SAT_ACT等出国语言培训机构. | 无土栽培|无土栽培技术|水肥一体化|无土栽培蔬菜| 芜湖禾风机械设备有限公司[官网] | 银泰洁净--净化工程总承包,20年精耕细作,专为净化而来_银泰洁净--净化工程总承包,20年精耕细作,专为净化而来 | 深圳诚暄软板首页-fpc软板,fpc软性线路板打样生产厂家 | 郑州试驾场地_双超专业汽车试驾场地_郑州双超文化传播有限公司官方网站 | 墨子百科-专业有趣的问题小百科 莫非传媒官网-江西知名的网络营销推广服务平台南昌网络公司,专业网络公关,品牌危机处理,网站SEO优化,微信朋友圈广告,网站建设,南昌莫非文化传媒有限公司 | 直膨式空调机组_风冷恒温恒湿_转轮式热回收_屋顶式空调机组_德州瑞尼森环保科技有限公司 | 中国(北京)国际园林绿化设备展览会| 氯化氢钢瓶回收_氯化氢气体钢瓶回收_山东言赫化工有限公司 | 一站式应用与数据集成平台(iPaaS) - 数环通 | 展柜设计定制-品牌展柜订做-展柜制作厂家「广州嘉艺展柜」 | 辽宁闻天香食品有限公司| 重大事件回顾:三亚哪里可以打炮?2025年最全实战攻略带你玩转真枪射击 | 久久91精品久久91综合_国产亚洲自拍一区_国产精品第1页_亚洲高清视频一区_91成人午夜在线精品_亚洲国产精品网站在线播放_亚洲国产成人久久综合区_国产精品亚洲专区在线观看_免费视频精品一区二区三区 | 医院,小型生活污水处理设备-山东明基环保设备有限公司 | 铸铁平台-铸铁平板平台厂家-加工优质高精度检验划线装配T型槽平台-尺寸规格全供应-建新铸造 | 宜宾三江人才网_三江人才网_宜宾三江人才网_三江人才直聘网是本地颇具规模的网上人才市场 | 找刑事辩护律师_找深圳刑事律师多少钱★王平聚【清华博士/刑法教授】 | 青浦区摄像头安装/青浦区无线网络覆盖/青浦区网络调试公司/青浦区IT外包公司/金山区网络维护公司/金山区防火墙调试公司 | 烟气在线监测系统_VOCs在线监测_分析仪「杭州世驰科技」 | 长沙变频器维修,变频器维修,ABB变频器维修,西门子变频器维修,施耐德变频器维修,伺服驱动器维修,工业机器人维修,20年专业工控电气维修,长沙文铖电气设备有限公司_长沙文铖电气设备有限公司 |