三菱PLC，欧美a级片免费看，三菱变频器，欧美a级成人淫片免费看，三菱伺服，欧美a大片，三菱电机--广州凌控

1. Outline of Product
The 232BD is an RS-232C communication board with a 9-Pin D-Sub. It is an insulated unit for signal
exchange. Connected to the main unit of the FX2N Series PLC,
it enables serial data transfer between the PLC and equipment via an RS-232C port.
1.1 Communication Functions and Applicable PLC
(Available in indicated version or later)
1.2 Outside dimensions and name of each part
The communication connector of the 232BD is the D-sub, 9-pin socket type. The table below shows the
pin arrangement.
1.3 System configuration
Only one function expansion board can be used for one main unit of FX2N.
FX2N-232-BD cannot be used by the plural. Other expansion boards cannot be used together with
FX2N-232-BD. For the system configuration, refer to the FX Series User's Manual - Data Communication
Edition offered separately.
2. Installation
Caution
• Use in the environments specified under the general specification in the manual.
Do not use the product in environments with excessive or conductive dust, corrosive or
flammable gas, oily smoke, moisture or rain, excessive heat, regular impact shocks or
excessive vibration, as it may result in electrical shock, fire, malfunction, damage or
deterioration on the product.
• Make sure to shut off the power outside the product before installing or wiring it.
Otherwise, electric shock or serious damage to on the product may occur.
• Never drop wire chips or shavings into the vent slits when drilling screw holes or performing
wiring, as they may cause fire, breakdown, or malfunction.
Securely install the 232BD to the designated port.
Poor connection may cause malfunction.
Communication
type
FX2N Function
Computer link V1.06
Data transfer via link protocol between PLC and computer
(specified as the master station).
No protocol
communication
V1.06
Serial communication without protocol between PLC and equipment via RS-232C
interface.
Optional
programming port
First
product
Optional port available for suitable programming tool when 232ADP is connected to
PLC.
Remote
maintenance
First
product
Program transfer or monitoring enabled via modem and phone line connected to serial
port of PLC.
Unit: mm (inches)
➀ Mounting hole (2-φ3.5)
➁ RXD LED: Lit during receive.
➂ TXD LED: Lit during send.
➃ Connector for RS-232C equipment
The top face of this connector is higher than the top face
of the PLC panel cover by approximately 7 mm (0.27").
➄ Hole for connector fixing screw (#4-40UNC)
➅ Connector for PLC
Accessories: Top cover for board 1
M3 screw to mount board 2
M3 s
PLC FX2N-16MR-001
PLC FX2N-128MT-ESS/UL
PLC FX2N-16MR-ES/UL
溫度控制模塊 FX2N-2LC
PLC FX2N-16MT-E/UL
輸入模塊 FX2N-8EX
PLC FX2N-64MS
繼電器輸出單元 FX2N-48ER
MELSEC-I/O LINK主站模塊 FX2N-16LNK-M
PLC FX2N-48MT-D
模擬量輸入輸出模塊 FX2N-5A
PLC FX2N-32MT-ESS/UL
繼電器輸出單元 FX2N-48ER-UA1/UL
晶體管輸出單元 FX2N-32ET
RS-485擴展板 FX2N-485-BD
PLC FX2N-48MT-ESS/UL
PLC FX2N-64MT-ESS/UL
擴展模塊 FX2N-8ER
模擬量輸入擴展板 FX2N-2AD-BD
PLC FX2N-48MS
PLC FX2N-48MS-E/UL
輸出模塊 FX2N-8EYR-ES/UL
溫度傳感器用模塊 FX2N-4AD-TC
PLC FX2N-128MT-D
晶體管輸出單元 FX2N-48ET
PLC FX2N-48MR-D
PLC FX2N-32MT-DSS
PLC FX2N-32MR-D
PLC FX2N-16MT-DSS
擴展模塊 FX2N-8EYR